Permabond ES05500320C0101

ES550 Toughened Non-Sagging Single-Part Epoxy, Gray, 320ml Cartridge

Permabond® ES550 is a single-part epoxy paste that is slump-resistant (does not flow) during cure. The adhesive is toughened for maximum impact resistance, along with excellent peel and shear strength. ES550 is ideal for bonding a wide range of materials including metals, ferrites, ceramics, and composites.

  • Excellent adhesive strength
  • Excellent resistance to vibration
  • Easy to use - no mixing required
  • High shear and peel strength
  • Good impact strength
  • High-temperature resistance
  • Good resistance to chemicals
USD 120.80
  • Comprar 2 por USD 117.18 cada uno
  • Comprar 6 por USD 113.55 cada uno

Documentos técnicos

Product Info & TDS Sheets

Physical Properties of Uncured Adhesive

  • Chemical composition: Epoxy Resin
  • Appearance: Silver-grey
  • Viscosity @ 25°C: 1,000,000 to 2,000,000 mPa.s (cP) (Helipath, 2rpm)
  • Specific gravity: 1.5
  • Flow at high temperature: No flow
  • Maximum gap fill: 5 mm 0.2 in
  • Cure speed (oven) *
    • 130° C (266°F): 75 minutes
    • 150°C (300°F): 60 minutes
    • 170°C (338°F): 40 minutes

*Actual cure times will depend on the time it takes for the adhesive to reach this temperature - for example, large assemblies or a crowded oven will require longer to reach full cure. Alternative, quicker methods of curing include induction, hotplates, infrared lamps, and hot-air guns.

Physical Properties of Cured Adhesive

  • Shear strength* (ISO4587)
    • Steel 27 - 41 N/mm2 (4000 - 6000 psi)
    • Aluminium 17-31 N/mm2 (2500-4500 psi)
    • Zinc 14 - 27 N/mm2 (2000 - 4000 psi)
  • Shear strength steel to ferrite: >14 N/mm2 (>2000 psi) Substrate failure
  • Impact Strength (ASTM D-950): 25-35 KJ/m2
  • Hardness (ISO868): 80-85 Shore D
  • E-modulus: 4.8 GPa
  • Elongation at break (DIN 53504): <3%
  • Coefficient of thermal expansion:
    • 45 x 10-6 mm/mm/°C (below Tg)
    • 160 x 10-6 mm/mm/°C (above Tg)
  • Thermal conductivity: 0.55 W/(m.K)
  • Glass transition temperature (Tg - DSC): 120°C (250°F)
  • Cure speed (induction): <3 minutes

*Strength results will vary depending on the level of surface preparation and gap.

" with "

Physical Properties of Uncured Adhesive

  • Chemical composition: Epoxy Resin
  • Appearance: Silver-grey
  • Viscosity @ 25°C: 1,000,000 to 2,000,000 mPa.s (cP) (Helipath, 2rpm)
  • Specific gravity: 1.5
  • Flow at high temperature: No flow
  • Maximum gap fill: 5mm 0.2 in
  • Cure speed (oven) *
    • 130° C (266°F): 75 minutes
    • 150°C (300°F): 60 minutes
    • 170°C (338°F): 40 minutes

*Actual cure times will depend on the time it takes for the adhesive to reach this temperature - for example, large assemblies or a crowded oven will require longer to reach full cure. Alternative, quicker methods of curing include induction, hotplates, infrared lamps, and hot-air guns.

Physical Properties of Cured Adhesive

  • Shear strength* (ISO4587)
    • Steel 27 - 41 N/mm2 (4000 - 6000 psi)
    • Aluminium 17-31 N/mm2 (2500-4500 psi)
    • Zinc 14 - 27 N/mm2 (2000 - 4000 psi)
  • Shear strength steel to ferrite: >14 N/mm2 (>2000 psi) Substrate failure
  • Impact Strength (ASTM D-950): 25-35 KJ/m2
  • Hardness (ISO868): 80-85 Shore D
  • E-modulus: 4.8 GPa
  • Elongation at break (DIN 53504): <3%
  • Coefficient of thermal expansion:
    • 45 x 10-6mm/mm/°C (below Tg)
    • 160 x 10-6mm/mm/°C (above Tg)
  • Thermal conductivity: 0.55 W/(m.K)
  • Glass transition temperature (Tg - DSC): 120°C (250°F)
  • Cure speed (induction): <3 minutes

*Strength results will vary depending on the level of surface preparation and gap.

Más información
SKU I167269
Modelo del fabricante ES05500320C0101
Marca Permabond
Tipo Epoxi sencillo
Volumen 320ml
¡Hemos encontrado otros productos que le pueden gustar!
©Production Automation Corporation. All Rights Reserved.